Design and optimization of broadband metamaterial absorber based on manganese for visible applications

Scientific Reports volume 13, Article number: 11937 (2023) Cite this article

1017 Accesses

2 Altmetric

Metrics details

Metamaterial absorbers have been extensively researched due to their potential applications in photonics. This paper presents a highly efficient Broadband Metamaterial Absorber (BMA) based on a Manganese–Silica–Manganese three layer structure with a shaped pattern at the top layer. For maximum absorption efficiency, the geometrical parameters of the proposed absorber have been optimized based on Particle Swarm Optimization (PSO). The optimal structure with a thickness of 190 nm, can achieve more than 94% absorption spanning visible band (400–800) nm with 98.72% average absorption, and more than 90% absorption over the range from 365 to 888 nm. In the range from 447 to 717 nm, the design presented above 99% absorptivity, providing an ultra-wide bandwidth of 270 nm. The physical mechanism of absorption is illustrated through the exploration of the electric and magnetic field distributions. Additionally, the proposed structure maintains 85% absorption stability for wide incident angles up to 70° for both the TE and TM polarizations under oblique incidence. Further, the optimized absorber structure with excellent absorption capabilities makes it suitable for various applications, including optical sensors, thermal emitters, and color imaging applications.

In the last decade, there has been a lot of interest in Metamaterial Absorbers (MAs), which are built with subwavelength-sized unit cells made of Metal–Insulator–Metal (MIM)1,2. The distinctive Electromagnetic (EM) properties of metamaterials, such as their negative permeability and negative dielectric constant3,4, make it possible to be efficiently applied to the various applications, such as solar energy harvesting5, wireless communications6, and sensors7. Extensive research based on MA designs has been published. Depending on the spectrum range in which the EM metamaterial operates, it may be easily operated for different frequencies, including terahertz8, visible, and infrared (IR) regimes9,10,11. For absorption bandwidth classification, narrowband MAs find applications in thermal emission manipulation, sensors, nano-antennas, and resonators12,13. Wideband absorbers, on the other side, have uses in thermal emitters, solar energy converters, and a variety of other optoelectronic applications14,15.

There has been a wide range of research activities in recent years that broaden absorption bandwidth to improve performance and increase capabilities. The first approach for achieving broadband absorption is to use multi-resonances by integrating various sizes of multiple resonators to form an absorber unit cell. Such absorbers offer high flexibility in achieving the desired absorption spectral properties by varying the geometry and structural dimensions of the resonators involved16,17,18. The second approach is to use multilayer structures with different geometrical parameters in the vertical direction, separated by dielectric layers, to broaden the absorption spectral bandwidth19,20. However, adding more layers entails intricate microfabrication processes and increased costs. This may obstruct the advancement of metamaterial absorbers. Consequently, it is essential to create simple topology metamaterial capable of achieving high-efficiency absorption21,22.

The MIM configuration can provide enhancement in absorption bandwidth. Up to date, several studies have been proposed to maximize absorption of MA structures in both intensity and broadband10,23. The most common method is optimizing the structure dimensions and shaping the top surface metallic layer of the metamaterial structure. For instance, a triangular prism shape metamaterial absorber with an average absorbance of 97.85% had achieved near perfectly absorption in the range of 200 to 2980 nm24. Another MA structure with a double sized axe-shaped resonator demonstrated more than 90% absorption in the visible to near-IR spectral range (i.e., from 320 to 982 nm)25. In addition, Majid Aalizadeh introduced metamaterial design based on a nanodisk-shaped resonator for light absorption spanning the visible to mid-infrared range (i.e., from 478 to 3278 nm), resulting in a wide band absorption26.

For the visible regime, many designs based on MIM configuration have been investigated. With the context, Lai et al.27 proposed a tri-layer MA based on Al–SiO2 with an average absorptivity above 95% from 450 to 600 nm range. However, the wavelength band is still insufficient to fulfil the rising demands for applications such as solar energy harvesting, which require ultra-broadband with perfect absorption characteristics. Moreover, polarization and oblique incidence sensitivity are not considered due to asymmetry structure. Sultan et al.28 investigated a star shaped resonator tri-layer MA with above 90% absorptivity from 389 to 697 nm and up to 60° incidence angle stability. The x and y dimensions of this structure are quite large. Bilal et al.29 introduced ultrathin broadband absorber comprised of tungsten nanowires with an absorption level of more than 80% and a band span of 400–750 nm. However, absorbers covering the entire visible spectrum with greater than 90% absorptivity are required.

A thin, broadband visible absorber with perfect absorption and a wide angle of incidence is the optimal design. In this paper, a novel absorber using Manganese (Mn) is designed, providing ultrahigh absorption for the entire visible range spectrum (400–800 nm). The proposed absorber structure is constructed based on MIM configuration, with a square disk surrounded by a square ring-shaped of Mn top layer and SiO2 dielectric spacer. To achieve the best performance of the proposed MA design, the Particle Swarm Optimization (PSO) algorithm is used to fine-tune the geometrical parameters of the absorber unit cell. In addition, the electric and magnetic field distributions are discussed to clarify the physical mechanisms underlying broadband perfect absorption.

The schematic representation of the proposed Broadband Metamaterial Absorber (BMA) is depicted in Fig. 1 which is obtained from the Lumerical FDTD solutions software30. The top most layer of a square disk surrounded by a square ring-shaped Mn acts as a resonator. SiO2 dielectric material is used to separate the top resonator from the bottom Mn layer.This spacer can assist in the construction of Fabry–Perot cavities and can also induce electromagnetic coupling between the top resonator and the bottom Mn layer. The reason for choosing Mn as the metal layer is its real part of permittivity, which varies slowly and covers the visible band. This makes it possible for the structure to be matched to the impedance of free space, leading to the strong penetration of the field22,31. It also exhibits strong absorption due to a large imaginary part of permittivity. In addition, Mn has the advantage of being less expensive than metals such as gold, which have been used in various patterned broadband absorbers22. It is also very advantageous to use low-cost materials to achieve compatibility for mass production. Figure 2a displays the effective refractive index (n) and the wave vector (k) of the complex refractive index of Mn, which are taken from Johnson and Christy's refractive index database32. SiO2 is employed as a dielectric material because its relative permittivity is low in the optical wavelength range11. The Palik model is used to represent the refractive index of SiO233.

(a) Schematic representation of a periodic array of the proposed broadband metamaterial absorber. (b) Top-view of a single absorber unit cell. (c) Side-view at the center of the absorber unit cell, which all are extracted from Lumerical FDTD solutions software30.

(a) Complex refractive index of Manganese (n and k), (b) Flow chart diagram of the applied PSO algorithm and (c) The average absorption with number of iterations of the applied PSO algorithm.

The proposed absorber structure consists of three layers Mn–SiO2–Mn with a periodicity (P) of 300 nm. The top square disk has a width of w1, and the square ring has a length (l) with a width (w2). The thicknesses of each layer from top to bottom are h1 and h2 for the top layer, h3 and h4 for the dielectric and substrate, respectively. The thickness of Mn substrate is selected to be greater than the skin depth \(\delta \left(\lambda \right)\) to which waves can penetrate. Equation (1) shows how the skin depth of a conductor is calculated34. where λ is the wavelength (m), ρ is the resistivity of a conductor (Ω m), μ is the permeability (H/m), and C is the speed of light in free space (m/s). For the electrical resistivity of Mn ρ = 144.2 × 10−8 Ω m, the skin depth at ranges from a low of 22 nm at wavelength of 400 nm to a high of 31.2 nm wavelength of 800 nm35. So, the Mn substrate having a thickness of 100 nm performs as a perfect reflector, resulting in structure transmission is approximately zero.

As known, The MA structures of different metal and dielectric layer thicknesses operate with varies range of frequencies. The thickness is a primary constraint in realizing a perfect absorber. With an aim to maximize the absorption more than 90% as well as minimize the absorber thickness, PSO algorithm is used for achieving the optimum solution to this problem. The geometrical parameters of the proposed design are suitably optimized for broadband perfect absorption and minimum absorber thickness.

The Finite Difference Time Domain (FDTD) approach is used to numerically model the absorption for our proposed structure, and the PSO algorithm is used to optimize the geometrical parameters. For FDTD simulations, Perfectly Matching Layers (PML) are utilized along the z direction, whereas Periodic boundary conditions are employed for the x and y directions. Mesh step settings are 5 nm, 5 nm and 1 nm in x, y and z-plane respectively. The parameters included in the optimization process are h1, h2, h3, w1 and w2. The other parameters which are l and h4 are fixed through the optimization process with 250 nm, 100 nm respectively. Figure 2b illustrates the basic steps of the applied PSO algorithm with a flowchart diagram. After defining the number of particles, number of iterations, and search space boundaries, the PSO algorithm begins by randomly generating initial particles within a specified range. Each particle stands for a possible solution to solve the optimization problem. Next, the absorption of each particle was then calculated using the FDTD method at wavelengths ranging from 400 to 800 nm according to Eq. (2), where A(λ) and R(λ) are absorption and reflection as a function of wavelength, respectively. The objective function is defined by summing absorption of levels more than 90% in 400–800 nm region. The optimization process aims to enhance the fitness value of the objective function to its highest potential.

The number of particles (N) and iterations (t) were set to 20 and 50 respectively. At each iteration, the maximum fitness value is identified as the local best. In case the new local best surpasses the global best, the global best is then updated with the new local best. When the number of iterations reached its limit, the optimization process came to an end. If not, the velocity of the particles and their new positions will be updated. The process of optimization was then repeated until the optimal geometrical parameters were attained. The average absorption of the proposed structure per iteration is illustrated in Fig. 2c. As shown, the average absorption remains constant for iteration number 12 and up. Consequently, the results of iteration number 12 are chosen as the geometrical parameters. According to the actual preparation process of geometrical parameters, we approximated their values to real integer numbers. For each parameter, the setting range is stated in Table 1 with its optimum value.

In this section, the advantages of absorption characteristics of the proposed MA structure are investigated. After the optimum geometrical parameters have been applied, the absorption spectrum under TE-polarized light is presented in Fig. 3a. The structure exhibits a strong absorption of more than 94% over a broad wavelength range, beginning at 400 nm and going up to 800 nm, and an absorption of more than 90% over the range from 365 to 888 nm. Using Eq. (3), we can figure out that the average absorption reaches up to 98.72% over the band of 400–800 nm. Perfect absorption (over 99%) is achieved from 447 to 717 nm with a bandwidth of 270 nm, and peak absorption is obtained up to 99.8% at the wavelength of 655 nm. Therefore, our results show that the proposed design with the optimized parameters yields great performance.

(a) Absorption of the proposed absorber design with the optimized parameters and (b) Effective input impedance of the absorber design.

The reason behind ultra-high absorption of the proposed structure is that its impedance matched with that of free space. If the scattering parameters (S-parameters) are known, it can be easily to attain a theoretical observation about this remarking. The scattering parameters for reflection and transmission are S11 and S21, respectively. S21 can be reasonably equal to zero owing to the presence of the thick metallic bottom layer. The effective input impedance (Zeff) of our proposed absorber can be obtained from S-parameters using Eq. (4) 36,37. Figure 3b displays the simulation results of the normalized Zeff for the pattern shaped Mn absorber. It can be clearly observed that real component of the structure impedance is close to 1, while the imaginary component is close to 0 through the visible regime (400–800 nm). This means that impedance of the pattern-shaped Mn absorber closely matches free space impedance.

To further illustrate why the proposed MA structure has broadband and perfect absorption, distributions of electric and magnetic fields (|E| and |H|) are simulated and shown in Fig. 4. Vertically TE-polarized waves of two resonant wavelength peaks, at 472 nm and 655 nm, are incident on the structure. Electrical distributions in the x–y plane are depicted in Fig. 4a,b, and electrical distributions in the z–y plane are depicted in Fig. 4c,d, respectively. The electric field is concentrated in the region between the square disk and square ring metals, and also focused around the metal edges of Mn. As a result, these distributions strongly suggest that Surface Plasmon Polaritons (SPP) are excited inside the structure37. However, the magnetic field distributions are clearly different. Specifically, at 472 nm seen in Fig. 4e, it is believed that the resonance is Propagating Surface Plasmon resonance (PSP). At the resonant wavelength of 472 nm, the magnetic field accumulated in the square disk Mn metallic top layer and SiO2 dielectric spacer, and it spread through the adjacent cells. This demonstrates that PSP resonance is responsible for the absorption around 472 nm5,25. Figure 4f shows that, at a wavelength of 655 nm, the magnetic field is strongly localized within the space between the top square disk of Mn and the Mn bottom layer. This confirms that the Localized Surface Plasmon resonance (LSP) has been excited25,38. The magnetic field distributions shown in Fig. 4e,f confirm the excitation of PSP and LSP resonances, which further widens the absorption bandwidth.

Electric field distributions (a,b) in the x–y plane and electric field distributions (c,d) in the z–y plane, and magnetic field distributions (e,f) of the proposed unit cell at different resonant wavelength peaks (472 nm, and 655 nm), respectively.

In addition, a comparison between absorption spectrum of the proposed MA with three other different configurations of the top layer resonators is investigated. The first configuration is a planar MIM continuous film in Fig. 5a which is performed to verify benefits of resonance modes. The other two configurations are a square ring and a square disk resonators. The layer thicknesses in all three configurations are consistent with the proposed design, and a single square disk with a length of 100 nm is utilized. Figure 5b displays absorption spectrum of the three configurations with our optimized absorber structure. For the planar MIM continuous film, the absorption of incident waves can be ascribed to the Fabry Perot cavity and the intrinsic loss of Mn. However, the absorption of the other two configurations (square ring and square disk resonators) are significantly increased due to plasmonic resonances. For our optimized absorber, designing a structure with two resonators in the unit cell can easily offer strong surface plasmon resonances. As previously demonstrated, strong interactions are generated with incident waves and excite strong plasmon (SPP, PSP and LSP) resonances. Therefore, the presence of both a square disk and a square ring resonators results in perfect absorption.

(a) a 3-D view of three different absorber configurations with the proposed design, and (b) Absorption spectrum for all three absorber configurations with the proposed one.

An excellent absorber should be as robust as possible to changes in the source incident angle (θ). As a result, the absorber design is subjected to further simulation for oblique incidence with both TE and TM polarization in order to determine the variations in absorption. The absorption spectrum under oblique incidence is seen in Fig. 6a,b With TE and TM polarization respectively. Owing to the symmetrical geometry of the structure, it absorbs incident waves with more than 85% regardless of polarization at oblique incidence up to 70°. However, absorption decreased significantly at incident angles greater than 70° due to the sensitivity of resonant natures to polarization and incident angle. Most of earlier works test absorber polarization at level of 70% absorptivity as illustrated in the Table 2 of comparison. Therefore, the absorption curves exhibit large incident angle insensitivity up to 80° under 70% absorptivity for both TE and TM polarizations, primarily because of the high symmetry39,40. That is one of the advantages of the proposed absorber design.

The structure absorption with incidence angle variation for (a) TE and (b) TM polarization.

Finally, the impact of using different metals and dielectrics on structure absorption is investigated. By replacing Mn from the top layer resonator and ground plane with different metals without changing any other dimensions. The response of the optimized absorber comprised of different metals such as Au, Cr, Al, and TiN is plotted in Fig. 7a. It is clearly observed that the absorption performance of metals such as Au and Al, suffers significantly. Even though when compared with absorber based on refractory metals such as Cr and TiN, it might accomplish significantly higher absorption. The reason of the behavior can be attributed to the wavelength-dependent refractive index of each metal. The plot also indicates that Mn based absorber is the best optimized for the proposed absorber because of the structure impedance matched to that of free space. The average absorption values of the stated metals are shown in Fig. 7b for the wavelength range of 400–800 nm. This figure implies that it is possible to replace Mn metal with TiN refractory metal while the average absorption is still high. However, the TiN-based absorber exhibits lower absorption spectra when compared to Mn. Figure 8 demonstrates the absorption spectra of the proposed absorber for different dielectric materials. The absorber is simulated with three dielectrics of SiO2, Al2O3, and TiO2, while the dimensions of the structure and the metal used (Mn) are kept the same. It is shown that the absorption shifted toward longer wavelengths as the refractive index of the dielectric material increased. Therefore, the dielectric of SiO2 has more contribution to the high average absorption than other dielectrics.

(a) Absorption spectra of the optimized structure with different metals and (b) Comparison of their average absorption.

(a) Absorption spectra of the optimized structure with different dielectric materials and (b) comparison of average absorption.

The comparison of earlier designs for visible band is presented in Table 2, with an emphasis placed on familiar characteristics such as absorption bandwidth, dimensions, material used, polarization independent and angle of incidence. It can be easily noticed that the proposed design covered all visible band compared with previous work with perfect absorption level. Broadband absorbers that can work through full region of visible band are relatively rare. Moreover, a perfect broadband absorber, with 98.72% average absorption and a resonance absorbance of 99.8% was found in our design. In addition to wide-angle sensibility at both TE and TM polarization up to 80° compared with earlier works at absorption level of 70%. The production costs are directly related to the materials used as well as the number of layers included. This design is unique in terms of thin structure, low material cost and easy fabrication in addition to high performance when compared to those stated in Table 2.

Broadband perfect metamaterial absorber for visible band from 400 to 800 nm numerically demonstrated. This absorber is constructed by Mn–SiO2–Mn three-layer structure, with 190 nm thickness. Selection of the geometrical parameters values of the absorber unit cell is based on Particle Swarm Optimization (PSO) algorithm. As a result of thickness optimization, the proposed metamaterial absorber has 98.72% average absorption over the wavelength range of 400–800 nm, and achieves perfect absorbance (above 99%) over the wavelength range of 447–717 nm. Moreover, the absorption still remains beyond 85% when the angle of incidence changes from normal up to 70° for both TE and TM polarization. Based on these characteristics, the proposed metamaterial absorber structure is an excellent choice for visible light applications such as optical sensors, thermal emitters, and color imaging.

The data sets used and/or analyzed during the current study are available from the corresponding author on reasonable request.

Banerjee, S. et al. Resonance phenomena in electromagnetic metamaterials for the terahertz domain: A review. J. Electromagn. Waves Appl. 34(10), 1314–1337 (2020).

Article ADS Google Scholar

Zhou, J. et al. Metamaterial and nanomaterial electromagnetic wave absorbers: Structures, properties and applications. J. Mater. Chem. C. 8(37), 12768–12794 (2020).

Article CAS Google Scholar

Ziolkowski, R. W. & Heyman, E. Wave propagation in media having negative permittivity and permeability. Phys. Rev. E 64(5), 056625 (2001).

Article ADS CAS Google Scholar

Grigorenko, A. N. et al. Nanofabricated media with negative permeability at visible frequencies. Nature 438(7066), 335–338 (2005).

Article ADS CAS PubMed Google Scholar

Gao, H. et al. Plasmonic broadband perfect absorber for visible light solar cells application. Plasmonics 15(2), 573–580 (2019).

Article MathSciNet Google Scholar

Siddiky, A. M. et al. A multi-split based square split ring resonator for multiband satellite applications with high effective medium ratio. Results Phys. 22, 103865 (2021).

Article Google Scholar

Tang, J., Xiao, Z. & Xu, K. Ultra-thin metamaterial absorber with extremely bandwidth for solar cell and sensing applications in visible region. Opt. Mater. 60, 142–147 (2016).

Article ADS CAS Google Scholar

Wang, B.-X. et al. A broadband terahertz metamaterial absorber enabled by the simple design of a rectangular-shaped resonator with an elongated slot. Nanoscale Adv. 1(9), 3621–3625 (2019).

Article ADS CAS PubMed PubMed Central Google Scholar

Bilal, R. M. H. et al. Elliptical metallic rings-shaped fractal metamaterial absorber in the visible regime. Sci. Rep. 10(1), 14035 (2020).

Article ADS CAS PubMed PubMed Central Google Scholar

Lei, L. et al. Ultra-broadband absorber from visible to near-infrared using plasmonic metamaterial. Opt. Express. 26(5), 5686–5693 (2018).

Article ADS CAS PubMed Google Scholar

Rana, A. S. et al. Tungsten-based ultrathin absorber for visible regime. Sci. Rep. 8(1), 2443 (2018).

Article ADS PubMed PubMed Central Google Scholar

Korkmaz, S., Turkmen, M. & Aksu, S. Mid-infrared narrow band plasmonic perfect absorber for vibrational spectroscopy. Sens. Actuators A 301, 111757 (2020).

Article CAS Google Scholar

Liao, Y.-L. & Zhao, Y. Ultra-narrowband dielectric metamaterial absorber with ultra-sparse nanowire grids for sensing applications. Sci. Rep. 10(1), 1480 (2020).

Article ADS CAS PubMed PubMed Central Google Scholar

Liang, Q. et al. Solar thermal absorber based on dielectric filled two-dimensional nickel grating. Opt. Mater. Express. 9(8), 3193–3203 (2019).

Article ADS CAS Google Scholar

Ghobadi, A. et al. Bismuth-based metamaterials: From narrowband reflective color filter to extremely broadband near perfect absorber. Nanophotonics 8(5), 823–832 (2019).

Article CAS Google Scholar

Ehsanikachosang, M. et al. Metamaterial solar absorber based on titanium resonators for operation in the ultraviolet to near-infrared region. J. Opt. Soc. Am. B. 39(12), 3178–3186 (2022).

Article ADS CAS Google Scholar

Patel, S. K. et al. Broadband metamaterial-based near-infrared absorber using an array of uniformly placed gold resonators. J. Opt. Soc. Am. B. 37(7), 2163–2170 (2020).

Article ADS CAS Google Scholar

Weng, Z. & Guo, Y. Broadband perfect optical absorption by coupled semiconductor resonator-based all-dielectric metasurface. Materials (Basel) 12(8), 1221 (2019).

Article ADS CAS PubMed Google Scholar

Abdelatif, G. Y. et al. Ultrabroadband absorber based on a funnel-shaped anisotropic metamaterial. J. Opt. Soc. Am. B 36(10), 2889–2895 (2019).

Article ADS CAS Google Scholar

Mehrabi, S., Rezaei, M. H. & Zarifkar, A. Ultra-broadband solar absorber based on multi-layer TiN/TiO2 structure with near-unity absorption. J. Opt. Soc. Am. B 36(9), 2602–2609 (2019).

Article ADS CAS Google Scholar

Guo, Y. et al. A simple topology metamaterial blackbody for visible light. J. Alloy. Compd. 699, 998–1002 (2017).

Article CAS Google Scholar

Aalizadeh, M. et al. Large-area, cost-effective, ultra-broadband perfect absorber utilizing manganese in metal-insulator-metal structure. Sci. Rep. 8(1), 9162 (2018).

Article ADS PubMed PubMed Central Google Scholar

Zhou, Y. et al. Broadband long wavelength infrared metamaterial absorbers. Results Phys. 19, 103566 (2020).

Article Google Scholar

Zhou, J. et al. Ultra-broadband solar absorbers for high-efficiency thermophotovoltaics. Opt. Express 28(24), 36476–36486 (2020).

Article ADS CAS PubMed Google Scholar

Tuan, T. S. & Hoa, N. T. Q. Numerical study of an efficient broadband metamaterial absorber in visible light region. IEEE Photonics J. 11(3), 1–10 (2019).

Article Google Scholar

Aalizadeh, M. et al. A route to unusually broadband plasmonic absorption spanning from visible to mid-infrared. Plasmonics 14(5), 1269–1281 (2019).

Article CAS Google Scholar

Lai, Y. C. et al. Extending absorption edge through the hybrid resonator-based absorber with wideband and near-perfect absorption in visible region. Materials (Basel) 13(6), 1470 (2020).

Article ADS CAS PubMed Google Scholar

Mahmud, S. et al. Design and parametric analysis of a wide-angle polarization-insensitive metamaterial absorber with a star shape resonator for optical wavelength applications. Results Phys. 18, 103259 (2020).

Article Google Scholar

Bilal, R. M. H. et al. Ultrathin broadband metasurface-based absorber comprised of tungsten nanowires. Results Phys. 19, 103471 (2020).

Article Google Scholar

Lumerical Inc. https://www.lumerical.com/products/fdtd/.

Aalizadeh, M., et al. Electromagnetic field tapering in the high-roughness substrates coated by a thin film of manganese: A lithography-free approach to ultra-broadband, wide-angle, UV to FIR perfect absorption. (2018).

Refractive index database. https://refractiveindex.info/.

Palik, E. D. Handbook of Optical Constants of Solids (Academic Press, 1985).

Google Scholar

Timsit, R. S. High speed electronic connectors: A review of electrical contact properties. IEICE Trans. Electron. E88-C(8), 1532–1545 (2005).

Article ADS Google Scholar

Desai, P. D., James, H. M. & Ho, C. Y. Electrical resistivity of aluminum and manganese. J. Phys. Chem. Ref. Data 13(4), 1131–1172 (1984).

Article ADS CAS Google Scholar

Ning, J. et al. An ultrathin tunable metamaterial absorber for lower microwave band based on magnetic nanomaterial. Nanomaterials 12(13), 2135 (2022).

Article CAS PubMed PubMed Central Google Scholar

Kim, I. et al. Thermally robust ring-shaped chromium perfect absorber of visible light. Nanophotonics 7(11), 1827–1833 (2018).

Article CAS Google Scholar

Li, W. et al. Refractory plasmonics with titanium nitride: Broadband metamaterial absorber. Adv. Mater. 26(47), 7959–7965 (2014).

Article ADS CAS PubMed Google Scholar

Dincer, F. et al. Design of polarization and incident angle insensitive dual-band metamaterial absorber based on isotropic resonators. Progr. Electromagn. Res. 144, 123–132 (2014).

Article Google Scholar

Huang, L. & Chen, H. J. P. I. E. R. Multi-band and polarization insensitive metamaterial absorber. Progr. Electromagn. Res. 113, 103–110 (2011).

Article Google Scholar

Hoa, N. T. Q. et al. Numerical study of an ultrabroadband, wide-angle, polarization-insensitivity metamaterial absorber in the visible region. J. Electron. Mater. 47(5), 2634–2639 (2018).

Article ADS MathSciNet Google Scholar

Zhou, Y. et al. Cost-effective near-perfect absorber at visible frequency based on homogenous meta-surface nickel with two-dimension cylinder array. Opt. Express 26(21), 27482–27491 (2018).

Article ADS CAS PubMed Google Scholar

Gomes de Souza, I. L. & Rodriguez-Esquerre, V. F. Omnidirectional broadband absorber for visible light based on a modulated plasmonic multistack grating. Opt. Laser Technol. 124, 105981 (2020).

Article CAS Google Scholar

Li, C. et al. Multipole resonance in arrays of diamond dielectric: A metamaterial perfect absorber in the visible regime. Nanomaterials (Basel) 9(9), 1222 (2019).

Article PubMed Google Scholar

Rahman, S., Islam, M. A., Alam, M. S. Design of a broadband metamaterial absorber for visible solar radiation entrapment. In 2021 IEEE International Conference on Telecommunications and Photonics (ICTP). 1–4 (2021).

Download references

The authors would like to express their gratitude to the National Telecommunication Regulatory Authority (NTRA), Egypt for their support.

Open access funding provided by The Science, Technology & Innovation Funding Authority (STDF) in cooperation with The Egyptian Knowledge Bank (EKB).

Electronics and Communications Department, Faculty of Engineering, Helwan University, Cairo, Egypt

Shimaa I. Sayed, K. R. Mahmoud & Roaa I. Mubarak

National Telecommunications Regulatory Authority (NTRA), Giza, Egypt

K. R. Mahmoud

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

S.I.S. performed the required simulations of the metamaterial absorber structure with associated potentials and wrote the original manuscript. K.R.M. contributed to the methodology and supervised the proposed work. K.R.M. and R.M. reviewed and edited the manuscript. All authors read and agreed to the final version of the manuscript.

Correspondence to Shimaa I. Sayed.

The authors declare no competing interests.

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

Sayed, S.I., Mahmoud, K.R. & Mubarak, R.I. Design and optimization of broadband metamaterial absorber based on manganese for visible applications. Sci Rep 13, 11937 (2023). https://doi.org/10.1038/s41598-023-38263-x

Download citation

Received: 10 May 2023

Accepted: 05 July 2023

Published: 24 July 2023

DOI: https://doi.org/10.1038/s41598-023-38263-x

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.